Freight density calculator with the 2025 NMFC scale
Calculate LTL freight density in pounds per cubic foot and find the class on the 13-subprovision NMFC density scale in effect since July 19, 2025.
Plan a shipping project
Calculator
Freight class for LTL shipments comes from the National Motor Freight Classification (NMFC), and many NMFC items set class by density. The NMFC changes that took effect on July 19, 2025 expanded the density scale those items use from 11 to 13 subprovisions, with new, lower classes for dense freight. This calculator works out the density of your handling units and shows where it falls on that scale.
Class depends on the item’s NMFC entry. Density alone does not set your class. Find the NMFC item for your commodity first. If it points to the density scale, the table below applies. If it carries a fixed class or its own subprovisions, use those. Your carrier’s tariff can add its own rules.
How to use the calculator
- Measure one handling unit, such as a pallet or crate, at its longest, widest and tallest points, including the pallet and any overhang.
- Enter the number of identical units. For units of different sizes, run each size separately and add up the cubic feet and weights.
- Enter the total weight of all units, including pallets and packaging.
The formula
Cubic feet = L × W × H (inches) × number of units ÷ 1,728
Density = total weight ÷ cubic feet (pounds per cubic foot)
There are 1,728 cubic inches in a cubic foot (12 × 12 × 12).
The density scale
| Sub | Density (lb per cubic foot) | Class |
|---|---|---|
| 1 | Less than 1 | 400 |
| 2 | 1 but less than 2 | 300 |
| 3 | 2 but less than 4 | 250 |
| 4 | 4 but less than 6 | 175 |
| 5 | 6 but less than 8 | 125 |
| 6 | 8 but less than 10 | 100 |
| 7 | 10 but less than 12 | 92.5 |
| 8 | 12 but less than 15 | 85 |
| 9 | 15 but less than 22.5 | 70 |
| 10 | 22.5 but less than 30 | 65 |
| 11 | 30 but less than 35 | 60 |
| 12 | 35 but less than 50 | 55 |
| 13 | 50 or more | 50 |
NMFTA’s published FAQ sets out subs 11 to 13, which are new. Subs 1 to 10 carry over from the earlier 11-sub scale; confirm them in NMFTA’s ClassIT+ before you rely on a result in those ranges. NMFTA calls the July 19, 2025 changes “only Phase 1” of a larger overhaul, so check for later dockets too.
Example (fictional). Two pallets of item EX-20118, each 48 × 40 × 52 inches including the pallet, weigh 1,640 pounds together. The NMFC item for the product uses the density scale.
- Cubic inches: 48 × 40 × 52 × 2 = 199,680
- Cubic feet: 199,680 ÷ 1,728 = 115.56
- Density: 1,640 ÷ 115.56 = 14.19 lb per cubic foot
- Density scale: 12 but less than 15 (sub 8), class 85
Reading the result
A density of 14.19 sits close to the break at 15. Built to 48 inches tall instead of 52, the same two pallets take 106.67 cubic feet, density rises to 15.38 and the class drops to 70. Four inches of height, from a tighter stack or a lower pallet pattern, moves the shipment a class. The reverse also happens: overhang adds volume, lowers density and can push freight into a higher class.
If the carrier’s measurements differ from yours, expect the invoice to follow theirs. Measure the way the carrier will, and keep the numbers with the bill of lading.
Common mistakes
- Leaving out the pallet, in height or in weight.
- Measuring cartons instead of the handling unit, which understates volume.
- Using density for an item with a fixed class in the NMFC.
- Using the old 11-sub scale, where everything at 30 pounds per cubic foot or more was class 60.
- Blending different products into one density when each has its own NMFC item.
When the simple model stops working
- Commodities with their own NMFC provisions, including fixed classes and item-specific subprovisions.
- Contract pricing that replaces class-based rates with other terms, such as freight-all-kinds agreements.
- Mixed shipments with several NMFC items, each classed under its own entry.
- Large or very light shipments, where carriers can apply space-based rules from their own tariffs.
- Later NMFC dockets, which can change items after this page was written.
This result is an estimate. Confirm the class against the NMFC item and your carrier tariff before you ship. Rating freight inside a TMS needs item dimensions, weights and NMFC items in master data, connected to carriers; that work is part of ERP, WMS and TMS integration. For parcel shipments, use the dimensional weight calculator.
Scope your project.
Tell us what you need to track, which systems you run and when it has to work. We reply with questions or a time to talk.